Specification:
Brand Name: Holybro
Model: Kopis Mini ( Analog VTX Version)
Item Name: 148.6mm F7 3 Inch FPV Racing Drone
Frame:3mm 3K Ccarbon Fiber
Wheelbase: 148.6mm
Wheelbase: 148.6mm
Flight Controller: Kakute F7 V1.5
ESC:Tekko32 F3 4in1 45A mini ESC
VTX: Atlatl HV V2
Motor: F1507 KV3800
Propeller: T3140
FPV camera: 1200TVL Foxeer Micro Razer FPV Camera
Receiver: Without Receiver / Frsky R-XSR Receiver ( Optional)
Receiver: Without Receiver / Frsky R-XSR Receiver ( Optional)
Adjustable camera uptilt from 0 degrees to 90 degrees
Buzzer included.
Battery plug: XT30
Weight:173g
Recommend Battery: 4S 650mAh~1300mAh Lipo ( NOT Included)
Features:
MCU: STM32F745 32-bit processor
IMU: MPU6000 (SPI)
Barometer: BMP280
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
TF card for Blackbox logging
Package Included:
|
olybro Kakute F7 V1.5 Flight Controller ( More Details) |
MCU: STM32F745 32-bit processor ( Manual)
IMU: MPU6000 (SPI)
Barometer: BMP280
Current Sensor: Approximately 130 amps maximum measurable value
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on
any UART without “uninvert hack”.
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not
supported.
TF card for Blackbox logging
Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 8g
|
|
Tekko32 F3 4in1 45A mini ESC ( More Details) |
Brand Name: Holybro
Model: Tekko32 F3 45A
Item Name: 45A BLheli_32 3-6S 4 in 1 ESC
Con. Current: 45A
Peak Current: 50A
- F3 MCU, runs double faster than F051
- 32bit ESC with BLHELI32 firmware
- Supports 3-6S lipo input
-PWM input, TLM supported
- Voltage output (VBAT)
- NO BEC
- Supports oneshot / Multishot / Dshot PWM
- Supports damped light
- Ext. cap needed for 6s (470uf 35v for 6s usage.)
- Mounting holes M2, 20x20mm
- Size:30 x 36 mm
- Weight: 7.8g
|
|
T-Motor F1507 3800KV Motor ( More Details) |
Brand Name: T-Motor Model: F1507 KV: 3800KV
Input Voltage: ( Lipo)3-4S
Configuration:12N14P
Shaft Diameter: 2mm
Idle Current ( 5V): 0.9A
Peak Current (60s): 23A
Max. Power:372W
Internal Resistance: 81mΩ
Lead: 24#AWG 100mm
Dimension:18.9x29.7mm
Weight: 15g ( Include Cable)
|
|
Holybro Atlatl HV V2 FPV Transmitter ( More Details ) |
Brand Name: Holybro ( VTX Manual) Model: Holybro Atlatl HV V2
Transmitting Output Power: 25mW/ 200mW/ 500mW/ 800mW Switchable
Audio: 6 MHz + 6.5 MHz Mono
Antenna Connector: MMCX
Input Voltage: 7-28V (2-6S Lipo)
Dimension: 35(L)x 25(W)x 7(H)mm
Mounting Hole: 30.5x30.5mm
Weight: 9.3g
|
Features:
MCU: STM32F745 32-bit processor
IMU: MPU6000 (SPI)
Barometer: BMP280
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
TF card for Blackbox logging
Package Included:
1x Kopis mini FPV racing drone
4x T3140 Propeller
1x Protective Case Mount for GoPro Hero5
1x Carying case
1x Battery strap(installed)
