OVERSKY NAZE32 B Flight Controller Board Build In DSM2 Receiver - 34.99 €

OVERSKY NAZE32 B Flight Controller Board Build In DSM2 Receiver
Seller: Banggood,
Ship from: CN Warehouse, Usually dispatched in 1-3 work days.

FREE SHIPPING: 10-35 days. (DHL faster please check price/quantity first)
Free shipping aviable, Registered postage from 25 €


OVERSKY NAZE32 B Flight Controller Board Build In DSM2 Receiver

















LED lights meaning:
Red LED—power; blue LED—flying mode; green LED—unlock;
How to connect a receiver:
Type A, type B and type C all gets a RX-S port (1.25mm 3P) which is special for connecting an outside receiver, it supports signal input of PPM, DSM2/DSMX, SBUS (note 1), it also support 3.3V or VIN output (Note 2), in order to connect an outside receiver, short connecting pads on RX-S and changing type of receiver on GUI at the same time is the way. Besides, type A, type B and type X all supports integrated DSM2 compatible 7CH receiver (Note 2)
Notes: 1) Type A and type B doesn’t support signal reverse but type X supports;
2) When output is VIN, and VIN>5.5V, please make sure if the outside receiver supports 5.5V or more, or the outside receiver may be burnt;
3) As it gets an integrated receiver, as soon as the integrated receiver is set to output banned(RF circuit of the integrated receiver won’t work at the moment), the outside receiver can work without problem.
Binding operation:
1) Press the binding switch on the receiver (green LED is on),then power FC board, release the binding switch, the green LED on the receiver flashes quickly (the receiver enters binding mode);
2) Press the binding switch on the DSM2 transmitter and then turn on the power;
3) When the fast flashing LED on the receiver is off and then comes to bright constantly, it indicates the binding is succeed, or repeat the above process.
Unlock operation:
Throttle to THR, Elevator to PITCH, Aileron to ROLL, Rudder to YAW
Unlocking: pull the throttle to the lowest, turn YAW to the right end (if it is still unlocking, please set range of YAW and THR to 120%, and check the channel direction and then try)
Question from customer:
I just received my Hermit quad, but I can't connect it to Cleanflight. I can't even flash any firmware, seems like it is soft bricked. On the normal Naze, I'd have to short the bootloader pins, but I can't find those on the MX Nano. Are there any on the board?
The answer:




Question and answer:
1)The description on how to wire the power is a bit unclear on your website.
Answer: please check the picture below for powering the FC:





2)What firmware and version comes pre-installed on the FC. Your help in providing this information would be greatly appreciated
Answer: CF_NAZE_32 V1.7.2
Question:Hi, I have a Hermit, and I'm trying to add an external PPM receiver.
I have it connected and its powered, and bound to my transmitter, but I think the board is not seeing the PPM stream.
As I understand, I need to jump two pads on the board for it to stop using the built in DSM2 and use the external RX? Can you show me a picture of which pads?
Answer: please check the following picture:




When I try to flash the board in Cleanflight, all I get is the error message of the bootloader. What do I do? I've tried many things but none have worked. It just said "bootloader error". What do I need to do?
Answer: The inside of red round is boot, the inside of the red square is 3.3V, please check the following picture:




Specification:
Super small size (not including its case): 32.0*19.6*10.5mm (Type A); 32.0*19.6*7.2mm(Type B)
Very light (not including its case and the integrated receiver): 3.2g (Type A), 2.9g (Type B);
Working voltage: Type A and B:5~10V; Type X: 3.3~4.5V or 5~10V;
12M/10PPM Crystal Oscillator;
Receivers it supports: PPM,DSM2,DSMX,SBUS;
Option for integrated with DSM2 compatible 7CH receiver;
Type X is with DCDC boost (output 5V/500mA),it can supply power for outside device;
The integrated output 5V/500mA LDO can supply power for outside device;
Independent ports for IIC, GPS, PPM/DSM/SBUS receivers;

Feature:
Come with DSM2 compatible 7CH receiver, sensor on it is MPU6050
Basis of the original NAZE 32, MX NANO OVERSKY 32 supports both Baseflight firmware and Cleanflight firmware, for using on different models, MX NANO
Notes: Type A gets 2.54mm pitch port, Type B and Type X is with 1.5mm pitch port.

Package Included:
1 X Flight controller

Add Comment





Finger-Clamp Pulse Oximeter Medical Finger Blood Oxygen Saturometro Heart De Oximeter Portable Pulse Oximetro Monitor

Interesting video

Latest views New