Sub250g FPV Drone Build - 02 - Frame, ESC & Motors
Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST:
SUPPORT ME ON PATREON at:
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: /
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Buy the Analog Sub250g build kit at:
* GetFPV -
* RaceDayQuads -
Buy the HD-Ready Sub250g build kit at:
* GetFPV -
* RaceDayQuads -
M2 screw assortment:
M3 screw assortment:
Practice solder board:
* GetFPV -
* RaceDayQuads -
ViFly Short-Saver
* GetFPV -
* RaceDayQuads -
---
All videos in this series are in this playlist:
---
00:00:00 - This is part of a series
00:01:06 - Mount the motors to the frame plate
00:04:12 - Assemble the front and rear bottom plates
00:08:09 - Install the FC
00:15:14 - Now the pain begins: soldering
The soldering tutorial that you should watch:
00:17:01 - Install the capacitor
00:20:51 - Solder the XT30 and capacitor to the FC
00:24:55 - Solder the motor wires to the ESC
00:30:05 - Smoke Check
00:33:08 - Conclusion
SUPPORT ME ON PATREON at:
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: /
---
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
Buy the Analog Sub250g build kit at:
* GetFPV -
* RaceDayQuads -
Buy the HD-Ready Sub250g build kit at:
* GetFPV -
* RaceDayQuads -
M2 screw assortment:
M3 screw assortment:
Practice solder board:
* GetFPV -
* RaceDayQuads -
ViFly Short-Saver
* GetFPV -
* RaceDayQuads -
---
All videos in this series are in this playlist:
---
00:00:00 - This is part of a series
00:01:06 - Mount the motors to the frame plate
00:04:12 - Assemble the front and rear bottom plates
00:08:09 - Install the FC
00:15:14 - Now the pain begins: soldering
The soldering tutorial that you should watch:
00:17:01 - Install the capacitor
00:20:51 - Solder the XT30 and capacitor to the FC
00:24:55 - Solder the motor wires to the ESC
00:30:05 - Smoke Check
00:33:08 - Conclusion
Racer.lt is not the owner of this text/video/image/photo content, the real source of content is Youtube.com and user declared in this page publication as Youtube.com user,
if you have any question about video removal, what was shared by open community, please contact Youtube.com directly or report bad/not working video links directly to video owner on Youtube.com. Removed video from Youtube.com will also be removed from here.
Watch more videos
-
Enduro Rally 2021 - Pabradė military base
Had a wonderful opportunity to be in a very dirty place on a badly rainy morning but with great a... -
Deathstroke 3d printed wearable mask #shorts
Deathstroke 3d printed wearable mask with X1C BambuLab #shorts #3dprinting #deathstroke #bamb... -
DLG - FLITZ - soaring joy!
The joy of DLG soaring! Pilot and Wing owner - Andrius Narbutas Bright LED: / - More products ...
Interesting video
